Plastic wedge soles

I made a wedge sole (shown on the right in the next picture) for making a latex mould, but then I realized that it would be fairly easy to use it to build a metal mould for casting plastic.

The moulds are made of thin copper sheet. Before cutting the sheet (with scissors, which have suffered quite a lot due to this habit), I covered it with clear packaging tape. This is meant for the inside of the mould to ensure that the plastic casting will have shiny surface. The pieces of the mould are held together by normal adhesive tape. Note that there are small pieces of wood under the toe part to keep the moulds straight.

The plastic I'm using is the type you need to heat in order to melt it. The brand name is E-Z Water and the only reason I'm using that is that it's the only brand I have found. The plastic is in the form of small grains.

The plastic is slightly yellow and if it gets too hot, it starts getting darker. I'm using the lowest possible temperature in which I can get it to melt, so the color won't change. Also, if the melted plastic is too hot, it will melt the packaging tape and the adhesive tape holding the moulds together. The result of that is a horrible mess as I once found out. Fortunately, I only managed to ruin the kitchen counter instead of burning myself with the stuff (even in the lowest temperature, it's still hot).

Before pouring the plastic into the mould, I placed a paper flower in the mould. As the flower had a stem, it was easy to hold it in place until the plastic had cooled down enough, so the flower would stay in place by itself.

You need to wait until the plastic has cooled down. Then you need to tear apart the mould to get the casting out. I usually do this when the casting is still a bit warm to touch, but not hot. Leave the casting to cool down properly after removing it from the mould.

Here are two pictures of a finished casting. There are some air bubbles in it, but I have noticed that it is almost impossible to avoid them altogether in castings of this size.


Here are the shoes I made using these castings. The ribbons are made of silk and the inner sole and strap are made of satin that was treated with sealer. The outer sole is again made of leather.



Original Finnish posts: Feb. 20, 2007, and July 7, 2007

High heel platforms

I decided to try a new way of making platform shoes. This time I wanted to make something higher than ever before.

I started by cutting suitable pieces from thick foamcore and glueing them in two layers.

Then I painted them to fill in the biggest gaps, although they would not have shown under the fabric anyway.

The arching part of the sole is made of several layers of cardboard (160 g/m2). I think I put 5-6 layers in these.

When making parts like this, you need to use glue that doesn't set right away. Start with two layers, spread glue on one and place the other on top of it. Then you form the desired shape and keep the pieces in that shape until the glue has dried enough to prevent the pieces from getting out of shape. Then glue the rest of the layers one layer at a time.

Then I glued the parts together. I noticed afterwards that it would have been better, if couple of the lowest cardboard layers had gone all the way down. It would have been easier to make the soles keep their shape that way.

I covered the shoes with fabric that I had treated with sealer. The heels are cut from thin metal pipe and the parts where they are attached to are made of modelling clay (the type that does not need to be oven baked).

I used the same fabric for inner soles and straps. I only used two straps for the shoes as the patterns of the fabric were decorative enough and there was no need for a more complicated design.

I covered the rest with the same fabric and glued small pieces of leather for taps and to the part that shows green in the picture below.

The picture below shows the finished shoes on the doll. I haven't tried it, but I don't think the doll could stand wearing these, because of balance issues.

Original Finnish post

Set of shoes for Tiny Betsy McCall

I had swatches of furniture fabric in several colors. I treated the fabrics with sealer (FolkArt Outdoor Satin Sealer) to prevent fraying and staining. After I had made shoes for larger dolls, there was still enough fabric left to make one pair of shoes in each color for Tiny Betsy.

This model is very simple. It requires minimum amount of glueing. The inner sole is made of the same fabric as the upper part. The outer sole is leather.

As the shoe has open toe, it is easy to glue. All you need to glue are the sides under the inner sole, the strap behind the ankle, and finally the outer sole. You can also glue a small piece of leather as the heel of the shoe.

You can use fairly thick fabrics for this model as the sides are straight, which makes it easy to glue them.


Here is the full set of shoes. Some of the decorations are glued to place, some attached with sewing thread.


If you want to try making this kind of shoes for your doll, here is the pattern. Save the picture on your computer and print it making sure that the scale in the picture matches reality.


If you make shoes using this pattern and put a picture of them on your web site, Flickr, etc., please leave a comment here telling me where to go to see the picture.

Original Finnish post

First post

My Finnish blog about doll shoes has had a lot of foreign visitors lately, so I thought maybe I could create an English version for those who do not understand Finnish. I will be adding stuff here occasionally (can't promise a frequent or regular update schedule as even the Finnish blog is updated sporadically).

For more pictures, you should see the Kenkäfriikki blog. I'll try to add here the posts that contain useful instructions.

If you would like to see a translation of a specific post in the Finnish blog, leave a comment here and I'll include it in my list of posts to be translated.