Baha Cat's boot lasts

The final piece of resin casting was making a pair of boot lasts for the Baha Cat. I used the last I made using balsa wood. I made one latex mold, then placed it beside the last when making the second one, so the two molds are connected and, thus, easier to keep upright when pouring the resin into them.

I cast a pair of lasts from the regular resin, and as I had some clear resin left, I used that for making an additional last just for fun.

More resin castings

As I was using the last of the resin as long as it was still usable, I decided to make some castings for boot making. For shoes, you only need the casting to be up to the doll's ankle, but I wanted to make boots for Gooliope. 16" dolls are especially difficult to handle when making shoes, so having just the leg below the knee makes things a lot easier. As I was going through the trouble, I thought I might as well make some others. The other doll in the picture below is a Living Dead Doll.

The picture shows how messy it is to create latex molds. Latex keeps dripping for some time after dipping the doll's feet to it, so you need some protection, in this case a newspaper, on the table.

At this point, I had to start calculating the amount of resin required, so I wouldn't have any resin mixed without having a mold to put it in. The easiest way to check the amount needed is to put some water in a measuring cup and put the doll's feet in it. The rise in the water level shows the amount needed. Unfortunately I didn't have a better measuring cup, so the numbers were only approximates, but that's better than nothing.

You also need to remember that if you're using resin with the ratio of 1:1 between resin and hardener, you need half of the measured amount of both. Elementary, but can be easy to forget when you keep thinking that one number you just measured.

The latex molds I made were fairly thin as you can see in the picture. They were only needed for one casting, so I didn't see any need to make them real sturdy. The third pair in the picture is for a My Little Pony Equestria Girls doll. 

Below are some castings waiting to harden. The big pair is for a 16" male doll by Robert Tonner. The ones with flat soles usually stay upright by themselves, but the Equestria girls molds needed some support, so I put them into a small plastic cup.

Finally, here are some hardened castings that have been removed from the molds. They still need to harden some more after removing them, although these are so thick that there was no risk of anything bending. When making shoe soles, it is important to always check immediately after removing them from the molds that the shape is correct, and if it is not, fix it as long as the resin is still soft enough to do it.

Soles and heels

Some time ago I had to get rid of some resin before it got bad, so I made some new masters for soles and heels. The soles were wedges, because those are much easier to handle when using latex molds. The master on the left is for Monster High Gooliope Jellington and the right one for 16" Miss Piggy.

Here are some of the soles I made after making the molds. The reddish sole in the middle has some glitter mixed in the casting resin. I wanted to see what that would look like. I'll probably just paint those soles when I use them for shoes. The clear sole isn't clear enough to my taste, so I guess clear resin should be used with silicone molds treated with wax.

The next one is a master for chunky heels. I haven't got any plans on how to use them, but I'm sure I'll come up with something

Another chunky heel, and yes, it's the right way up. Browsing books about shoes can give you some strange ideas.

As I had some transparent resin, I decided to try heels that could be filled with glitter or beads or some other small items. Master in the middle, two latex molds on the sides.

I'm not sure the heels are transparent enough, but maybe they'll work. Or they can be left empty and used as clear heels that were just made using a method that saves resin.

Plaster casting continued

I used the molds for plaster casting and also experimented on using a latex mold to make polymer clay heels. I had never done that before, but thought it was worth trying.

Plaster casting with latex molds

The latest video is about making latex molds of heels for plaster casting.

First video tutorial

I just filmed the first video tutorial of the new series. It's about making latex moulds of a doll's feet.


The next video will be about using foot moulds to make castings.

New foot lasts

Going through the stuff inspired me to do something else as well. I decided to use the rest of the casting resin before it goes bad. The latex is also getting a bit thick, so it's better to use it as well. So, I'm making some more foot lasts.

All this has been done before and posted in this blog, but here are some photos anyway. The first one shows Sybarite's feet with flower tape around the ankles and several layers of latex applied.

The next one is Tonner's Jessica Rabbit (17" athletic body). First with flower tape covering the ankle joints...

...and then with latex applied.

Here are the finished moulds for both.

And here are the resin castings made with the moulds. You can see the flower tape clearly, but it is much neater than saran wrap.

As you can see in this photo showing the earlier plaster castings of Sybarite's feet and the new resin castings.

Replicas of MH Catty's boots

I got Monster High Catty Noir and seeing her boots got me thinking that I might be able to copy them. The boots consist of two halves, which should make it possible to make tubular latex moulds for them.

I attached the parts to small pieces of cardboard covered with packing tape. I used clear mounting tape to attach the pieces from the toe parts and them applied a few coats of latex. I had to make moulds for all four parts, because the two halves of one boot were different and the corresponding parts for the other boot were mirror images of those.

Here are two of the finished moulds. I was a bit worried that the holes wouldn't be big enough to get the pieces out of the moulds, but latex stretches quite a lot, so the moulds were usable.

Here you can see the size of the holes. The biggest problem with them came when pouring resin into the moulds as it would easily spill outside the mould.

Making the castings wasn't as straight forward as I had thought, because hanging the moulds vertically caused the moulds to deform as resin collected to the bottom. I had to fill the moulds half full first and place them almost horizontally so they would keep their form. Then when the resin had hardered a bit, I could pour in the rest and keep the moulds upright to keep the resin from spilling out.

Here you can see the original pair and the resin castings. The castings aren't quite successful as the seam in front won't close properly, but the result is still better than I expected. I'll just need to figure out a way to fix the front.

More resin casting

I have continued my experiments with latex moulds. I'm still having trouble with very small/thin parts, so when I decided to try Barbie-sized soles, I chose wedges. I had a cheap set of shoes for Steffi and picked a pair of those. In the photo, you can see an original shoe, one with straps removed, a resin casting, and the latex mould. Pouring resin into a mould this small is challenging, as is getting all air bubbles out, but it can be done.

Another part of my experiments is making foot lasts for all 1/6 scale dolls. In the photo below, the foot lasts from left to right belong to these dolls: Hollywood Royalty Lana Turner, Silkstone Barbie, Tiny Kitty Collier, Monster High Howleen, Bratzillaz, and Pinkie Cooper.

Using the high heel tubular mould

I thought the latex mould should be entirely dry already, so I made the first soles using it. My first idea for removing air bubbles from the heels worked just fine. I pressed the heel closed, poured in some resin, released the heel, and checked it. There was a small air bubble inside it, so I tilted the mould a bit and  squeezed the air out of the heel.

Then I released the heel again and this time it was full of resin, so I filled the rest of the mould.

The shape of the mould required building a support for it, so no resin would spill out.

And here is the finished casting. It is better to be able to make these with latex moulds as I only made two soles to get one pair of shoes. I don't make that many shoes for Rini, for whom these are intended, so it would be too expensive to use silicone for a mould for these.

Tubular mould for a high heel sole

Latex is so much cheaper than silicone that I'm now trying to make all possible moulds using latex. Looking at a master for a high heel sole, I got an idea I just had to try. I thought that it would be possible to make a tubular mould using latex by placing the opening under the toe part and attaching the master to a support only from that place. The picture below explains this better than any words. I used a square piece of mounting tape to attach the master to the cardboard structure.

Then I applied several layers of latex, letting it dry before applying the next layer.

Here you can see the size of the opening. It is fairly large, because the entire master needs to fit through it.

This is the trickiest part of removing the mould. You need to roll the mould over the highest part of the master, because too much stretching could tear the latex at this stage.

Here is the mould turned right side out. I'm going to let it set for a few days before casting, because removing the castings will require a lot of stretching and I want to be sure the mould can take it.

It'll be interesting to see how this will work. I got the master out of the mould, so removing the castings should not be a problem. Getting air bubbles out of the heel could be a challenge, but I already have a theory on how to do that. We'll see how it works once I get to use the mould.

Casting resin: Feet with ankle joints

When I was ordering resin, I didn't realize that the bottles I got for my first try were 100 ml and the ones I ordered now were 250 ml. That's 0.5 liters of resin and it's a lot when making as small castings as doll shoe soles. So, I decided to make several castings of doll feet now that I found out I can use latex moulds. I've only got 500 g of silicone and that doesn't make many moulds, because you need so much of it around the master. 300 ml of latex, on the other hand, is enough for a bunch of moulds.

I wanted to find a better way of making castings of feet with ankle joints. The first time I tried it, I used saran wrap to protect the ankles and the resulting castings weren't very pretty, even though they were perfectly usable.

This time I was wondering if flower tape would do the job. It's stretchy and slightly adhesive, but not so much that it would leave glue stains to the doll's feet.

Monster High Deuce got to be the guinea pig for this experiment. I wrapped flower tape tightly around his ankles and then applied a few layers of latex.

The moulds weren't too hard to remove, even though flower tape has matte surface. You just need to make sure there are no open seams for the latex to go into and everything should work fine. Below are the finished moulds with some supports and ready for casting.

This is what the castings look like. Much neater than when using saran wrap. These are for making shoes with low heels, so that's the reason for the angle of the ankle.

Resin casting with latex moulds

As I was reading the instructions of the casting materials I bought, it started to look like latex moulds could be used for resin casting. Of course I had to try it. For the experiment, I chose making castings of the Hollywood Royalty Lana Turner's feet. Plaster castings of that size are not very durable, so I thought it would be great to have them made of resin.

The earlier blog post about making foot lasts can be found here. This time I was using latex meant for making tubular moulds, so it worked a lot better.

When I made the latex moulds, I made small tabs on the back, so it would be easy to hang the moulds from the clips in my magnifying glass. Hanging them helps to keep the correct form while the resin hardens.

I treated the insides of the moulds with form releasing wax to protect the latex and to help remove the castings. I'm happy to say that the casting was successful and I now have resin foot lasts for Lana. There was an air bubble in her left big toe, so that's a small flaw, but it does not affect the usability of the lasts.

I also made some resin shoe soles using latex moulds. Unfortunately, the latex seems to deteriorate very quickly when used for resin casting. It can be used, but I didn't manage to make very many castings with one mould before holes started to appear. That could be due to not having just the right kind of form releasing agent. There are so many different varieties that it is hard to know, which one should be used. I used what I happened to have and it was the wax I bought for making and using silicone moulds.

I'm currently writing the chapters about mould making, casting, and doll feet, so this was part of the experiments I'm doing to figure out what needs to be included in the instructions. Doing it all as I'm writing also helps to remember things that have gone wrong and to find out new things that can go wrong, so I can include tips for avoiding those.

Unfinished projects

I've been doing some cleaning and there are a lot of unfinished projects, some of which may never be finished. I decided to collect some of them to this post.

First, a pair of Barbie stilettos, which were bright pink to start with. I painted them black using acrylic paint and then added sealer to prevent the paint from chipping. These are unfinished, because I haven't figured out what kind of straps to use and how to attach them.

Next, a pair of plaster castings for Monster High dolls. The first stage was making a master using balsa wood.

Here's the sanded and painted master with another one made of modeling clay.

Making the latex mould. If you want something else than a wedge sole with this technique, the easiest option is to make the back of the heel straight, so the opening can be placed there.

A pair of plaster soles right out of the mould.

Here after a few coats of paint. And that's how far this project has come.

Then another Monster High repaint. The next stage will be painting the round studs, but I've been postponing that, because I know how hard it will be with eyesight like mine.

The final one is an experiment with shrinking plastic. It's a thin sheet of plastic (white, opaque or transparent), which shrinks and hardens when you bake it in the oven. The first picture shows the piece I made to get the right measurements. The scale drawn in the piece of plastic was originally 3 cm long.

When you bake the pieces, they first curl and then straighten back. The result is flat, if the oven temperature is just right.

I used the plastic sheets to make the same kind of heels as in the shoes made entirely of cardboard. Far right is the pattern in the correct size, far left the pattern enlarged to take the shrinking into consideration, and in the middle is the baked plastic heel.

Here you can see the difference in thickness. The upper piece I'm holding is an unbaked sheet and the lower one is a baked piece.

I have also made the straight parts of soles for these and glued the heels into them, but that's where this project has stopped, at least for now. The next stage would be to make the inner soles, probably out of cardboard as usual.