Fixing the loafers

The second try on the loafers was more successful. In the photo below, you can see the soles (black, made of the same old mousepad as the sandal soles), paper pattern, pattern cut from clear plastic (more durable than paper), and the vertical side pieces. The soles are smaller this time. I traced the foot on paper and just rounded the result, not adding any extra length.

This time I used hot glue for attaching the side pieces around the edges of the soles. I even used it for the back seam, overlapping the edges a bit. Hot glue works extremely well with felt. I had soles made of air-drying modeling clay for which I used hot glue to attach the felt, didn't like the result and tried to remove the felt. Can't be done. The felt gets so effectively stuck that if you mess up, you cannot remove it and try again, you need to start from scratch.

The top of the shoes is similar to the first attempt. I tried making it narrower first, but it didn't work with these smaller soles, so the pattern for the top part was drawn the same way as in the first time. Basically, everything else was fine in the first time, just the soles were too big.

Here's another picture from a different angle. I'm still thinking about adding some decorations, but haven't figure out what those would be. The main thing for now is that the pattern and structure work, you just need to get the size of the soles correct.

Simple loafers

This is the sole I made for the Kindi Kids sandals. You just trace the doll's foot on paper and then shape the sole around it. This time I used it for making loafers out of felt.

Here are the pieces for the shoes. The grey soles are made of thick felt (0.3 mm) that is made of recycled textiles. The red parts are made of thinner felt I bought from a supermarket's crafts section. The uppers are shaped using the sole pattern and adding a small bit that won't be sewn into the side pieces, so it will turn up along the top of the foot.

I sewed the side pieces to the soles and then the back seam. Then tried this on the doll to check how it looked like.

The sides of the toe part were too high, so I adjusted them while the doll's foot was inside the shoe. Then I wrapped the remaining side piece around the shoe to adjust it the same way before sewing it in place in the other shoe.

Then I sewed the uppers in place. At this point I realized that the upper should have been narrower than the sole, but I wasn't going to undo anything and just accepted that this first try wasn't going to be a success. The soles need to be smaller anyway, so I'll make all the necessary adjustments in the next pair of loafers.

Here are the finished shoes on the doll. Not totally awful, but definitely in need of improvement. This doll's feet are so oddly shaped that it is a challenge, but I'm sure I'll be able to make a nicely fitting pair eventually.

Sandals using hot glue

I have been practicing with hot glue, and the Kindi Kids doll I have is perfect for this. The proportions of the doll are so off that it doesn't matter, if the shoes look a bit clumsy.

I'm also practicing with some new materials. The first of those is the black foam I used for the soles of these shoes. It's from an old mousepad. I just removed the fabric covering of the mousepad, and the material was easy to cut with scissors. It's soft, but still sturdy as the mouse pad was 0.5 cm thick.

As usual, I started by tracing the doll's foot on paper and then shaping the sole around that. Then I cut the soles from the mousepad.

For straps, I used this Christmas decoration material. It resembles the material I used for the stiletto heels, but it's not as stiff as that was. I expect to be making several pairs of shoes while experimenting with this material as there's 2 meters of it in the roll.

Here are the main parts of the shoes. On the left, the ends of the straps are cut in a way that they can be placed slightly slanted on the sides of the soles. At this point, the straps are a bit too long as it is better to leave some extra and trim that away while checking how the other end should be glued.

I used hot glue for every part of the assembly. Here the blue headed pin marks the place for the front edge of the strap.

I first glued one end and then checked with the doll how long the straps should be and where the other ends need to be glued.

After gluing the other ends in place, I glued vertical pieces behind the heels for attaching ankle straps. I also glued some of the red material on the edges of the soles where they remained bare.

The ankle straps are made of three thin rubber bands. I glued the ends inside the heel part, because that was the only place to hide them. Another option would have been to make a knot and let it show on the outside or cover it with some decoration.

Here are the finished shoes. The soles could have been shorter, and maybe the strap should have had only three rows to show the toes, but these are good enough for a first try with new materials, new kind of glue and new type of doll.

Variation of the stiletto heels

These shoes are made with similar resin soles as the red stiletto heels. The previous post shows the painting stage. I wanted different heels for these, but ended up using the same structure underneath. I don't remember what kind of glue I used for the red pair, but this time I used hot glue to secure the wooden sticks in place.

I painted the heels black, and while the paint was drying, I thought about different ways of using the plastic material also in the heels in addition to using it for the straps. I ended up with the structure below in which the bottom pieces are first glued in place around the heel and then the upper part.

Here are the finished shoes. The plastic parts of the heel are glued in place using hot glue, while the straps over the toe part are sewn in the similar way as in the red shoes. 

Painting resin soles

I have two more pairs of the soles I used for the stiletto heels. I like resin soles, because you can do so much more with them than with plaster castings, but the thing I'm not that fond of is the painting required. It took over a week to get these painted because enamel paints have such a long drying time.

Now I'm trying to decide the type of heels and the uppers for the yellow shoes. The black ones will have the uppers made of the black and silver material in the picture below. It's similar to the all silver material I used for the red shoes. I also found some fairly similar material last weekend (the red and gold ones in the photo), except a lot cheaper, 4 cm wide and 2 meters in a roll and only cost 1€ per roll. Of course I had to get some, although not for these shoes. I think the yellow ones will have something different for uppers.

The next problem is figuring out the heels. I have plenty of those round wooden sticks I used for the stiletto heels, but I want something different for these. Maybe using the sticks as a support inside and building something fancy around them. I guess it's time to go browsing my collection of shoe pictures to get ideas.

Monster High shoes

The final wall-hanging display case has really small spaces, so only fairly small shoes fit into it. Mainly that means Monster High dolls, Sybarite and CED dolls. The link info below the picture again states for which dolls the shoes are made.

Row 1 - Decorative copper shoes, Madame Alexander's Alex: second pair, third pair; Tonner's Tiny Kitty: fourth pair, fifth pair

Row 2 - Monster High: first pair, second pair, third pair, fourth pair; Tonner's Tiny Kitty: fifth pair

Row 3 - Monster High: first pair, second pair, third pair, fourth pair, fifth pair

Row 4 - Monster High: first pair; Rini: second pair

Row 5 - Sybarite: first pair, second pair, third pair, fourth pair, fifth pair

Row 6 - Sybarite: first pair, second pair

Row 8 - CED doll (Finnish blog): first pair, second pair

Row 9 - CED doll (Finnish blog): first pair, second pair

Another wall-hanging display case

Here is another display case hanging on the wall. The shoes in it are for Monster High Nefera, Tonner's Jessica Rabbit, Tonner's 16" Miss Piggy, Madame Alexander's Cissy, and Tonner's American Model. The link info below the picture will state which dolls the shoes are for.

Row 1 - Nefera; Jessica Rabbit: second pair, third pair, fourth pair

Row 2 - Miss Piggy: first pair, second pair

Row 3 - Miss Piggy: first pair, second pair

Row 4 - Miss Piggy: first pair, second pair

Row 5 - Cissy (Finnish blog), American Model

Row 6 - Cissy: first pair (Finnish blog), second pair (Finnish blog)